Planet WGSD-10020 Manuel d'utilisateur Page 30
- Page / 553
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
User’s Manual of WGSD-10020 Series
30
Reset Button Pressed and Released
Function
< 5 sec: System reboot Reboot the Managed Switch
> 5 sec: Factory Default
Reset the Managed Switch to Factory Default configuration.
The Managed Switch will then reboot and load the default
settings as below:
。 Default Username: admin
。 Default Password: admin
。 Default IP address: 192.168.0.100
。 Subnet mask: 255.255.255.0
。
Default Gateway: 192.168.0.254
2.1.2 LED Indications
The front panel LEDs indicates instant status of port links, data activity and system power; helps monitor and troubleshoot when
needed. Figure 2-3 & Figure 2-4 shows the LED indications of these Managed Switches.
WGSD-10020 LED indication
Figure 2-3 WGSD-10020 LED panel
System
LED Color Function
PWR Green
Lights to indicate that the Switch has power.
Per 10/100/1000Mbps port
LED Color Function
1000
LNK/ACT
Green
Lights to indicate the port is running in 1000Mbps speed and successfully established.
Blink: indicate that the switch is actively sending or receiving data over that port.
10/100
LNK/ACT
Green
Lights to indicate the port is running in 10/100Mbps speed and successfully established.
Blink: indicate that the switch is actively sending or receiving data over that port.
- User’s Manual 1
- TABLE OF CONETNTS 3
- 1. INTRODUTION 20
- 1.3 How to Use This Manual 22
- 1.4 Product Features 23
- 1.5 Product Specification 26
- - Port Number 27
- 2. INSTALLATION 29
- 2.1.2 LED Indications 30
- 2.1.3 Switch Rear Panel 32
- 2.2 Install the Switch 33
- 2.2.2 Rack Mounting 34
- 3. SWITCH MANAGEMENT 38
- 3.3 Administration Console 39
- Direct Access 40
- 3.4 Web Management 41
- 4. WEB CONFIGURATION 43
- 4.1 Main Web Page 46
- 4.2 System 48
- 4.2.1 System Information 49
- 4.2.2 IP Configuration 50
- 4.2.3 IPv6 Configuration 51
- 4.2.4 Users Configuration 52
- Add / Edit User 53
- 4.2.5 Privilege Levels 55
- 4.2.6 NTP Configuration 57
- 4.2.7 UPnP 58
- 4.2.8 DHCP Relay 59
- 4.2.9 DHCP Relay Statistics 61
- 4.2.10 CPU Load 63
- 4.2.11 System Log 64
- 4.2.12 Detailed Log 65
- 4.2.13 Remote Syslog 66
- 4.2.14 LED Power Reduction 67
- 4.2.15 EEE Power Reduction 68
- 4.2.16 Thermal Protection 69
- 4.2.17 Web Firmware Upgrade 70
- 4.2.18 TFTP Firmware Upgrade 71
- 4.2.19 Configuration Backup 72
- 4.2.20 Configuration Upload 74
- 4.2.21 Factory Default 75
- 4.2.22 System Reboot 76
- 4.3.1 SNMP Overview 78
- 4.3.4 SNMPv3 Configuration 82
- 4.3.4.2 SNMPv3 Users 83
- 4.3.4.3 SNMPv3 Groups 85
- 4.3.4.4 SNMPv3 Views 86
- 4.3.4.5 SNMPv3 Access 87
- 4.4 Port Management 89
- 4.4.4 Port Statistics Detail 92
- 4.4.5 SFP Information 95
- 1000Base-SX 95
- 1000Base-LX 95
- 100Base-FX 95
- 4.4.6 Port Mirror 96
- Mirror Port Configuration 97
- Buttons 98
- : Click to save changes 98
- 4.5 Link Aggregation 99
- 4.5.1 Static Aggregation 101
- 4.5.2 LACP Configuration 103
- 4.5.3 LACP System Status 104
- 4.5.4 LACP Port Status 105
- 4.5.5 LACP Port Statistics 106
- 4.6 VLAN 107
- 4.6.2 IEEE 802.1Q VLAN 108
- ■ 802.1Q VLAN Tags 109
- 4.6.3 VLAN Basic Information 111
- 4.6.5 VLAN Membership 116
- 4.6.6 VLAN Membership Status 117
- 4.6.7 VLAN Port Status 119
- 4.6.8 Private VLAN 120
- 4.6.9 Port Isolation 121
- 4.6.10 VLAN setting example: 123
- 4.6.10.3 Port Isolate 128
- 4.6.11 MAC-based VLAN 130
- 4.6.12 MAC-based VLAN Status 131
- 4.6.13 Protocol-based VLAN 132
- 4.7 Spanning Tree Protocol 135
- 4.7.3 Bridge Status 143
- 4.7.5 MSTI Priorities 147
- 4.7.6 MSTI Configuration 147
- Configuration Identification 148
- MSTx MSTI Port Configuration 150
- 4.7.8 Port Status 151
- 4.7.9 Port Statistics 152
- 4.8 Multicast 154
- Type Response Time 156
- 4.8.5 IGMP Snooping Status 161
- 4.8.6 IGMP Group Information 163
- 4.8.7 IGMPv3 Information 163
- 4.8.11 MLD Snooping Status 168
- 4.8.12 MLD Group Information 170
- 4.8.13 MLDv2 Information 170
- 4.8.14 MVR 171
- 4.8.15 MVR Status 173
- 4.9 Quality of Service 175
- 4.9.2 Port Policing 176
- 4.9.3 Port Classification 177
- 4.9.4 Port Scheduler 179
- 4.9.5 Port Shaping 180
- 4.9.6 Port Tag Remarking 182
- 4.9.7 Port DSCP 183
- 4.9.8 DSCP-Based QoS 185
- 4.9.9 DSCP Translation 187
- 4.9.10 DSCP Classification 190
- 4.9.11 QoS Control List 191
- 4.9.12 QoS Status 195
- 4.9.14 QoS Statistics 197
- 4.9.16 Voice VLAN OUI Table 200
- 4.10 Access Control Lists 201
- 4.10.3 ACE Configuration 204
- MAC Parameters 206
- IP Parameters 209
- ICMP Parameters 210
- TCP/UDP Parameters 211
- Ethernet Type Parameters 212
- 4.11 Authentication 216
- System Configuration 222
- Port Configuration 225
- Port State 233
- Port Counters 234
- Selected Counters 237
- Attached MAC Address 238
- 4.11.7 RADIUS Overview 243
- 4.11.8 RADIUS Details 244
- RADIUS Accounting Servers 248
- 4.12 Security 259
- 4.12.2 Access Management 262
- 4.12.4 HTTPs 264
- 4.12.5 SSH 265
- 4.12.6 Port Security Status 266
- Port Status 267
- 4.12.7 Port Security Detail 268
- 4.12.8 DHCP Snooping 269
- 4.12.12 ARP Inspection 273
- 4.13 Address Table 276
- 4.14 LLDP 282
- 4.14.3 LLDPMED Configuration 285
- Coordinates Location 286
- Civic Address Location 287
- Port Policies Configuration 290
- 4.14.4 LLDP-MED Neighbor 291
- node behavior for the 294
- 4.14.6 Port Statistics 296
- 4.14.7 Port Statistics 297
- 4.15 Network Diagnostics 300
- 4.15.2 IPv6 Ping 301
- 4.15.3 Remote IP Ping Test 302
- 4.15.4 Cable Diagnostics 303
- 4.16.2 Power Configuration 306
- 4.16.3 Port Configuration 309
- 4.16.4 PoE Status 310
- 4.16.5 PoE Schedule 311
- 5. COMMAND LINE INTERFACE 313
- Configure IP address 314
- 5.2 Telnet Login 316
- 6. Command Line Mode 317
- Example: 325
- 6.2 IP Command 326
- 6.7 Security Command 359
- Security Network ACL Delete 407
- 6.9 Link Aggregation Command 440
- 6.11 LLDP Command 447
- LLDP Info 452
- 6.12 LLDPMED Command 453
- LLDPMED ECS 454
- LLDPMED Port Policy 456
- 6.13 EEE Command 459
- 6.15 Thermal Command 465
- 6.16 LED Power Command 467
- LED Power Configuration 468
- QoS QCL Delete 486
- 6.18 Mirror Command 489
- 6.19 Configuration Command 491
- 6.20 Firmware Command 492
- 6.21 UPnP Command 494
- 6.22 MVR Command 496
- 6.23 Voice VLAN Command 500
- 6.24 IPMC Command 507
- IPMC Parameter URI 517
- 7. SWITCH OPERATION 523
- 7.5 Auto-Negotiation 524
- What is PoE? 525
- The PoE Provision Process 527
- Classification 528
- Start-up 528
- Operation 528
- 9. TROUBLE SHOOTING 530
- APPENDEX A 532
- 1 2 3 4 5 6 7 8 533
- APPENDEX B : GLOSSARY 534
- EC Declaration of Conformity 552
Produits connexes et manuels pour Routeurs Planet WGSD-10020
Routeurs Planet WGSD-10020 Manuel d'utilisateur
(557 pages)
(557 pages)
Routeurs Planet WGSD-10020 Manuel d'utilisateur
(373 pages)
(373 pages)
Routeurs Planet WGSD-1022 Manuel d'utilisateur
(355 pages)
(355 pages)
Routeurs Planet WGSW-2620HP Manuel d'utilisateur
(211 pages)
(211 pages)
Routeurs Planet WGSW-50040 Manuel d'utilisateur
(437 pages)
(437 pages)
Routeurs Planet WGSW-5242 Manuel d'utilisateur
(286 pages)
(286 pages)
Routeurs Planet WGSW-52040 Manuel d'utilisateur
(505 pages)
(505 pages)
Routeurs Planet WGSW-52040 Manuel d'utilisateur
(876 pages)
(876 pages)
Routeurs Planet XGS3-24040 Manuel d'utilisateur
(582 pages)
(582 pages)
Routeurs Planet XGS3-24040 Manuel d'utilisateur
(869 pages)
(869 pages)
Routeurs Planet XGS3-24042 Manuel d'utilisateur
(721 pages)
(721 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.145 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels